2008 honda civic steering wheel emblem

Is it possible to remove the original silver emblem piece on the steering wheel? I already ordered and received a red and silver emblem to replace it but can't seem to figure out how to remove the original one

disconnect the negative terminal on the battery so you don't blow the horn.

Get something thin enough to get underneath the original emblem and start working at it to pry it off evenly, so you don't break it.

Then just 3M double side tape the JDM one in its place.

^ that, but one thing i noticed when i put my emblem on.. after a few days the tape didn't work as well as it should.. so i went out and bought some silicone glue, you should find it at an auto store or a hardware store. there's a DIY about the specific kind to use somewhere..

theres gotta be some kind of way of removing the airbag cover.

somebody should make a DIY for this im having the same prob.

i attempted for 2 secs to try and remove the plastic H but mine wouldnt budge.

I did this a while back. The problem is that it is held in my numerous plastic/rubber pieces. I took a tiny screwdriver to pry a small section up a little and used a razor blade to just cut the pieces away from the emblem. Looks like crap after and you are left with little white dots where the holes are but if you have the emblem to go in there it dosent matter in my book. After I cut them all I just pressed the new emblem that I got from graffix and it was done. I would take pics but I don't want to screw up my new emblem more than it already is.......long story on that but has nothing to do with removing the Chrome emblem. When I order my new emblem in the next couple days ill take a few pics after I take the messed up one off so you can see what I'm talking about.

You're gonna need pliers and a sharp knife/ exacto. Start pulling from the corners and as you come across the plastic tabs cut them carefully.
First picture shows you the beating your original emblem will take lol. Second pic shows you where all the tabs are.

You're gonna need pliers and a sharp knife/ exacto. Start pulling from the corners and as you come across the plastic tabs cut them carefully.
First picture shows you the beating your original emblem will take lol. Second pic shows you where all the tabs are.

image

image

image

Perfect....lol. now I don't have to take the pics.

Looks really clean. Mine ended up in like 4 pieces.

Where can replacement emblems be found? Also, what if I just want a normal one without the red back?

The yellow plastic is showing through mine since I bought the car and I hate it. It's time to clean it up.

Just put the new emblem over it. If u take it off u will regret it

I don't really care about destroying the emblem and the new type r emblem I got has some sticky tape on the oposite side like a sticker.. it doesn't quite look like yours tho it has clear edges and its like the emblem coated in the clear ill take pics later.. prob just not as good quality as yours

I got the old emblem out and put the new one on I didn't do a great job how did you get it on so clean?

Its sort of above the engraved leather I used double sided tape on the whole piece any help?

And where did you get that emblem? I got mine off ebay.. yours is clearly what I was searching for

And where did you get that emblem? I got mine off ebay.. yours is clearly what I was searching for

GRFXP.com. They just got a connection and they can finally get us these. I was sick of rocking that red sticker.

thanks for this...i was wondering the same thing

GRFXP.com. They just got a connection and they can finally get us these. I was sick of rocking that red sticker.

How did you get yours on so well?

Silver H was removed and replaced with this. I had to use a little bit of sealant to make it look stock

Ok, I am kinda liking the red one. Where can I get it?

I have one of the hard red ones but u will need some new tape or sealant to install it. I bought a replacement emblem off eBay and just painted it. Much cleaner looking install over the overlays IMO