How to connect chamberlain garage door opener to remote

Home » DIY » Remotes » How to program a Chamberlain Clicker Universal Remote Control / LiftMaster 375?

The Chamberlain Clicker Universal Remote Control (KLIK1U, KLIK3U, KLIK3U-BL, KLIK3U-PK)

aka LiftMaster 375UT (375 LM) is a universal remote that

will program to most garage door openers and external receivers using learn buttons or DIP switches.

The first step is determining if your garage door opener or external receiver uses a learn button or DIP

switches.

Newer garage door openers utilize a learn button

and older units utilize DIP switches.

Programming the clicker universal remote to a garage door opener/receiver with learn button:

1. Start with the garage door closed.

2. Open the remote by sliding the battery cover open. Inside the remote you will see a

program button on one side and DIP switches on the other side. Press and hold the program

button for about 2 seconds, until the LED light illuminates.

3. Press the learn button on the garage door opener or external receiver. The learn button will be

on the back or side of the garage door opener motor. You will have to use a ladder to locate and

access the learn button. Always use caution any time you use a ladder to prevent accidental

falls.

4. Press and release the button on the remote you want to operate the garage door opener. Wait

until the LED on the remote stops flashing between button pushes. Continue to press the

button until you hear a click from the garage door opener, the light on the garage door opener

flashes or the garage door starts to open.

5. Press and release the program button to exit the programming mode.

6. Press the button you just programmed to verify the garage door opener remote is programmed

and the garage door opens and closes using the remote. If the garage door does not open and

close, repeat the programming steps.

These same steps work for programming to an external receiver or a gate opener with a learn button.

Number of button pushes required for the following Openers to program the universal clicker:

(Number of times press and release require / Learn button and Years

Brand / Models)

1 Time

Linear Mega-Code 1997-current

LDCO800, LCO75, LCO50, LDP50, LDO3, MVP50, LSO50, LDCO850, LDCO852, LDO33,

2 times	Red / Orange Button 1997 – 2005 (Security+ 390Mhz)
Brand	Models
Chamberlain	2200, 4200, 4620, 4640, 6200, 7220, 7320, 7420, 7902, 8200, 9200, 9902, 9950, 9960,CG40, PD210, PD212, PD420, PD420-2, PDPD610, PD612, PD752, PD785S, WD912K, WD922K
LiftMaster	985, 9851,1000SDR, 1200, 1240R, 1245R, 1246R, 1255R, 1256R, 1265, 1280R, 2000SDR, 2110, 2220, 2245, 2255, 2575, 2280, 2500, 2500B, , 2500D, 2580, 2589, 2265, 2565, ATS211R, ATS211X,
Craftsman	139.5399211, 139.53672, 139.53978SRT, 139.53995SRT, 139.53993D, 139.53992D, 139.53992, 139.53991, 139.53491SRT

Master Mechanic 642-2MM

3 times	Purple Button 2005 – Current (Security+ 315Mhz)
Brand	Models
Chamberlain	248730, 48930D, 7520, 9950D DCG40D, CG42D, HD200D, HD400D, HD420D, HD422D, HD600, HD800D, HD900D, LW2000, LW3000, LW3500, PD210, PD210D, PD212D, PD300, PD432D, PD462D PD610D, PD612D, PD612KLD, PD752D, PD758D, WD822KD, WD832KD, WD952KD, WD952LD WD962KD
LiftMaster	1345, 1346, 1355, 1356, 3110, 3130, 3220, 3240, 3245, 3255, 3265, 3280, 3500, 3575, 3585, 3595, 3800, 3800P, 3800PLD, 3850, ATS2113X, ATS2113X-CX, HCT501130, LGO50113R, LGO20113XR
Craftsman	139.53997D, 139.53985DM, 139.53990DS, 139.5399011,

Access Master M385,

4 Times

Chamberlain / LiftMaster

/ Craftsman

Green Button

1993 – 1996

710WHC, 711WHC, 1100, 2100, 4100, 4600, 5100, 7200, 8100, 8100M, CSO, 1240, 1245, 1246, 1250, 1255, 1260, 1260LK, 1245LK, 1270, 1280, 1000SD, 2000SD, 215WD, 220WD, 315WD, 320WD, ATS211, 53479

5 Times

Genie Ovearhead Door Intelicode 2005 – Current

ChainMax 1000, ChainMax 1200, ChainMax 1200 4042, SilentMax 750, SilentMax 1000, SILENTMAX 1000 3042, SILENTMAX 1200, SILENTMAX 1200 4042, TriloG 1200, TriloG 1500, TriloG 1500 4064, TriloG 1500 4064H, PowerLift 900, PowerMax 1200, PowerMax 1500, IntelliG 1000, IntelliG 1000 3024, IntelliG 1000 3024H, IntelliG 1200, IntelliG 1200 4024, IntelliG 1200 4024H, CB 1000, CB 1200, 1022, 1024, 1028, 1035, 1042, 2020, 2022, 2024, 2028, 2035, 2036, 2040, 2040L, 2042, 2055, 3035, 3055, 3064, 7035, 7055, BeltLift 600, Directlift 2060, Directlift 3060, GPower 900, Machforce 4062, Excelerator 4062, SilentMax Connect, SteakthDrive 750, StealthDrive 750 Plus,

6 Times

Genie Ovearhead Door Intelicode 1995 – Current

H8000, 4560, 500ML, 700ML, Excelerator, GCG350,

350L, 350L-1x, 350L-2, 350L-2C, 350L-2WK, 350L-2WKC, Chain Glide, H2000,

OverHead Legacy

7 Times

Stanley Security Code 1998

8 times	Yellow Button 2011 – Current (Security +2.0)
Brand	Models
Chamberlain	B353, B373, B500, B503, B510, B550, B550C B730, B740, B750, B970, B1381, B2202, B2212T, B2405, B4505T, B4545, B4603T, B4613T, B4643T, B6713T, B6753T, B6765, C203, C205, C253, C273, C450, C2102, C2202, C400, C410, C450, C455, C870, C2212T, C2405, 349544, 349544EV, D2101, HD220, HD220C, HD420EV, HD520EV, HD750WF, HD920EV, HD930EV, HD950WF, LW260C, LW2200 LW3000EV, LW5000EV, LW9000WF, PD220, PD222, PD612EV, PD752KEV, PD762EV, RJ020, RJ070, WD832KEV, WD850KEV, WD930EV, WD962KEV, WD962KPEV, WD962MLEV,
LiftMaster	8010, 8065, 8075, 8155, 8155W, 8160W, 6180WB, 8164W, 8165, 8165W, 8365-267, 8365-267W, 8355, 8355W, 8360, 8360W, 85503-267, 8557, 8557W, 8587, 8587W, 8500, 8500W, 8550, 8550W, 8550W-267, 85503, 84501, 84602, 87802, 87504-267,
Raynor	Ultra II, Admiral II, Prodigy II, Aviator II, Pilot II, Sergeant II, Airman II, Corporal II, Prodigy II , Sentinel, Voyager,

Do-It, Master Mechanic, True Value

Access Mater – M885, M8856

Craftsman -CMXEOCG471,CMXEOCG981, CMXEOCG231,CMXEOCG571, CMXEOCG771, CMXEOCG781

9 Times

Wayne Dalton Rolling Code 372.5 MHz 1999 – Current

3014, 3018, 3018DLX, 3514, 3314, 3414, 3220C, 3222C, 3224C, 3320B, 3322B, 3322B, 3324B, 3212, 3213, 3312, 3313, 3412, 3012, 3016, 3512

14 Times

Linear Multicode 10 Position Dip Switch

16 Times

Stanley Multicode 10 Position Dip Switch

18 Times

Linear Multicode 8 Position Dip Switch

Remember the LED light on the clicker must stop flashing between each press of the button during

programming.

If your garage door opener or receiver utilizes DIP switches you must match the DIP switches on the

remote to the DIP switches on the garage door opener or receiver. It could be 8-12 DIP switches with 2

or 3 positions per switch. The DIP switches much match identically. If your garage door opener or

receiver has only 2 positions and programming does not work, switch the off and on positions on the

remote as they may be reversed.

Program chamberlain garage door opener and clickers, in general, is a fairly simple process if you follow the listed procedures. You can

contact a local garage door service company to provide the remote and program the remote for you.

Labor rates will vary depending on your area but is normally around $70 – $120 (Include full garage door

and opener inspection) and the cost of the universal clicker remote is around $35 – $50.

Need garage door repair in Dallas tx? call us today

Fill Out The Form

How do I pair my remote to my garage door opener?

Press and release the LEARN button on the garage door opener unit. The learn indicator light will glow steadily for 30 seconds. Within this 30 second time period, press and hold the button on the hand-held remote. Next, release the button when the overhead opener unit's lights blink.

Where is the Learn button on the Chamberlain garage door opener?

The Learn button on your garage door opener is located above the antenna wire that hangs from the motor head, or it may also be under a light cover. The Learn button will be either green, red/orange, purple or yellow.

connect chamberlain garage door opener remote

How to connect chamberlain garage door opener to remote

The Chamberlain Clicker Universal Remote Control (KLIK1U, KLIK3U, KLIK3U-BL, KLIK3U-PK)

aka LiftMaster 375UT (375 LM) is a universal remote that

will program to most garage door openers and external receivers using learn buttons or DIP switches.

The first step is determining if your garage door opener or external receiver uses a learn button or DIP

switches.

Newer garage door openers utilize a learn button

and older units utilize DIP switches.

Programming the clicker universal remote to a garage door opener/receiver with learn button:

1. Start with the garage door closed.

2. Open the remote by sliding the battery cover open. Inside the remote you will see a

program button on one side and DIP switches on the other side. Press and hold the program

button for about 2 seconds, until the LED light illuminates.

3. Press the learn button on the garage door opener or external receiver. The learn button will be

on the back or side of the garage door opener motor. You will have to use a ladder to locate and

access the learn button. Always use caution any time you use a ladder to prevent accidental

falls.

4. Press and release the button on the remote you want to operate the garage door opener. Wait

until the LED on the remote stops flashing between button pushes. Continue to press the

button until you hear a click from the garage door opener, the light on the garage door opener

flashes or the garage door starts to open.

5. Press and release the program button to exit the programming mode.

6. Press the button you just programmed to verify the garage door opener remote is programmed

and the garage door opens and closes using the remote. If the garage door does not open and

close, repeat the programming steps.

These same steps work for programming to an external receiver or a gate opener with a learn button.

Number of button pushes required for the following Openers to program the universal clicker:

(Number of times press and release require / Learn button and Years

Brand / Models)

1 Time

Linear Mega-Code 1997-current

LDCO800, LCO75, LCO50, LDP50, LDO3, MVP50, LSO50, LDCO850, LDCO852, LDO33,

2 times

Red / Orange Button 1997 – 2005

(Security+ 390Mhz)

Brand

Models

Chamberlain

2200, 4200, 4620, 4640, 6200, 7220, 7320, 7420, 7902, 8200, 9200, 9902, 9950, 9960,CG40, PD210, PD212, PD420, PD420-2, PDPD610, PD612, PD752, PD785S, WD912K, WD922K

LiftMaster

985, 9851,1000SDR, 1200, 1240R, 1245R, 1246R, 1255R, 1256R, 1265, 1280R, 2000SDR, 2110, 2220, 2245, 2255, 2575, 2280, 2500, 2500B, , 2500D, 2580, 2589, 2265, 2565, ATS211R, ATS211X,

Craftsman

139.5399211, 139.53672, 139.53978SRT, 139.53995SRT, 139.53993D, 139.53992D, 139.53992, 139.53991, 139.53491SRT

Master Mechanic 642-2MM

3 times

Purple Button 2005 – Current

(Security+ 315Mhz)

Brand

Models

Chamberlain

248730, 48930D, 7520, 9950D DCG40D, CG42D, HD200D, HD400D, HD420D, HD422D, HD600, HD800D, HD900D, LW2000, LW3000, LW3500, PD210, PD210D, PD212D, PD300, PD432D, PD462D PD610D, PD612D, PD612KLD, PD752D, PD758D, WD822KD, WD832KD, WD952KD, WD952LD WD962KD

LiftMaster

1345, 1346, 1355, 1356, 3110, 3130, 3220, 3240, 3245, 3255, 3265, 3280, 3500, 3575, 3585, 3595, 3800, 3800P, 3800PLD, 3850, ATS2113X, ATS2113X-CX, HCT501130, LGO50113R, LGO20113XR

Craftsman

139.53997D, 139.53985DM, 139.53990DS, 139.5399011,

4

Times

Chamberlain / LiftMaster

/ Craftsman

Green Button

1993 – 1996

710WHC, 711WHC, 1100, 2100, 4100, 4600, 5100, 7200, 8100, 8100M, CSO, 1240, 1245, 1246, 1250, 1255, 1260, 1260LK, 1245LK, 1270, 1280, 1000SD, 2000SD, 215WD, 220WD, 315WD, 320WD, ATS211, 53479

5 Times

Genie Ovearhead Door Intelicode 2005 – Current

6 Times

Genie Ovearhead Door Intelicode 1995 – Current

H8000, 4560, 500ML, 700ML, Excelerator, GCG350,

350L, 350L-1x, 350L-2, 350L-2C, 350L-2WK, 350L-2WKC, Chain Glide, H2000,

OverHead Legacy

7 Times

Stanley Security Code 1998

8 times

Yellow Button 2011 – Current

(Security +2.0)

Brand

Models

Chamberlain

LiftMaster

8010, 8065, 8075, 8155, 8155W, 8160W, 6180WB, 8164W, 8165, 8165W, 8365-267, 8365-267W, 8355, 8355W, 8360, 8360W, 85503-267, 8557, 8557W, 8587, 8587W, 8500, 8500W, 8550, 8550W, 8550W-267, 85503, 84501, 84602, 87802, 87504-267,

Raynor