Whirlpool side by side ice maker replacement

Ice Maker Removal:

This style of icemaker is mounted sideways at the top of the freezer compartment and is covered by a door flap. There is also a spring-loaded flap on the left side of the freezer that will open and block the emitter board whenever the freezer door is opened. This will break power to the ice maker whenever the door is opened and keep you from getting showered with freshly produced ice cubes when you’re grabbing some tasty treat.

Step 1. Unplug the refrigerator…Safety First! (Note: some tests may require electrical current. Proceed with caution and at your own risk.)

Step 2. Remove the ice maker cover by applying sideways pressure and pulling slightly.

Step 3. Remove one ¼” screw from that right bottom of the ice maker that secures the wire harness cover. Then remove the cover by pulling it toward the back of the freezer.

Step5. Unplug the wire harness. You now have an ice maker in your hands… Now what? Take a look at “Ice Maker Test Points” for more testing help.

Ice Maker Parts:

The Whirlpool in-door ice system uses ice maker part#2198597 and part#W10190961 for 22cf. models

The Whirlpool modular ice maker mechanics are examined in detail at this link “Whirlpool modular icemaker” Note: the in-door ice system ice maker differs from the ice maker described in this video in the following ways: There are several additional trim pieces that direct air flow and direct ice into the door bin as it harvests.  It also has a slightly different fill cup for top fill vs. rear fill.

In that note the water supply tube which supplies water to the 

Step 1. Remove the ice maker.

Step 2. Disconnect the water supply tub from the back of the refrigerator at the “John Guest” disconnect fitting. (To release the tubing from the fitting press the tubing into the fitting while pressing and holding a small ring into the fitting. This will allow you to pull the tubing free from the fitting.)

Dispenser Parts:

What if your ice maker is pumping out ice like a lover scorned but the dispenser just won’t put out…

There are quite a few elements that deliver ice from the bin to your glass so here is an overview of the process and the components involved.

When you press the paddle of your dispenser a mechanism opens the ice shoot door and a switch is closed that should energize a motor in the freezer door.  When the motor is activated it turns a drive shaft that connects to the bottom of your ice bin.  This causes the wavy arm in your ice maker bin to turn and push ice down through the open shoot for your icy refreshment…

Common Problems With The In-Door Ice Dispensing System:

“I can’t get any ice to come out of the dispenser.”

“I don’t hear the motor at all.”

Is the dispenser lock button on? Does your freezer light switch work? You may have a power supply problem in the dispenser switch pack or the motor has completely given up. 

(Shock Hazard! Voltage must be present for these tests.)You can check the motor for voltage by removing the motor cover at the bottom of that big blank bulge in your freezer door.  (Double check your wire diagram for test points and wire colors.) Your freezer door switch needs to be taped closed so that power is supplied to the circuit.  Then with the motor plugged in check for 115 ACV from the two center contacts. (Usually blue and white) when the ice dispenser paddle is depressed. Next check for VDC 115 across the two right most connections and the two left most connections (Orange/Blue to Pink/Black) and (Red/White to Brown/White) when the ice dispenser paddle is depressed, on both crushed and cubed settings.

Take a look at the dispenser strip circuits below.

“The motor just makes a humming noise.”

Remove the ice bin and also remove the bracket that holds the drive coupling from the motor into place.  Now pull the drive shaft up and out, close the door and try it again if the motor is still just humming you probably need to replace the dispensing motor. If that fixed it, check that the arm in the ice bin moves freely and look for anything that might cause the shaft to bind up.

“There is a bunch of frost in the dispenser shoot and ice bin.”

Frost in the ice shoot or bin almost always is a sign of an air leak. After all it’s an ice maker not a frost machine. You can check for air leaks by removing the ice bin and shining a flashlight down into the ice shoot, then look for light from the outside of the dispenser shoot.  You may also see a cylinder looking device attached to the dispenser door. This is a suction tube that has a plunger inside that slows the closing of the door for quiet operation.  If the door is not closing all the way you may try removing this device and scratching a line or two on the inside of the cylinder. This will allow the door to close more quickly, for a slightly stronger seal there will also be slightly more noise as the door is closing.(Tip: If you are going to attempt to repair or replace the ice dispenser door or dispenser switch move slow take pictures and don’t remove more parts than you must.)

“The Ice bin is one big clump of ice.”

This is actually fairly normal and the ice bin should be emptied of old ice on a regular basis to prevent damage to the ice bin. However, if the ice is freezing together very quickly (less than a week or two) you may have an air leak at the ice shoot door.  You can check for air leaks by removing the ice bin and shining a flashlight down into the ice shoot, then look for light from the outside of the dispenser shoot. You may also see a cylinder looking device attached to the dispenser door. This is a suction tube that has a plunger inside that slows the closing of the door for quiet operation.  If the door is not closing all the way you may try removing this device and scratching a line or two on the inside of the cylinder. This will allow the door to close more quickly, for a slightly stronger seal there will also be slightly more noise as the door is losing.(Tip: If you are going to attempt to repair or replace the ice dispenser door or dispenser switch move slow take pictures and don’t remove more parts than you must.)

How do you change a Whirlpool side by side ice maker?

How long do Whirlpool ice makers last?

Why is my side by side Whirlpool refrigerator not making ice?