Enter the characters you see belowSorry, we just need to make sure you're not a robot. For best results, please make sure your browser is accepting cookies. Type the characters you see in this image:Try different image Conditions of Use & Sale Privacy Notice © 1996-2015, Amazon.com, Inc. or its affiliates 3 Button Remote OPERATING INSTRUCTIONSWARNING Moving Door can cause serious injury or death. • Wall Console must be mounted in sight of door, at least 5 feet above fl oor and clear of moving door parts. • Keep people clear of opening while door is moving. • Do NOT allow children to play with the Remote or door opener. If safety reverse does not work properly: • Close door then disconnect opener using the manual release handle. • Do NOT use Remote or door opener. • Refer to Door and Door Opener Owner's Manuals before attempting any repairs. 1 PROGRAM THE OPENER PROGRAM PRESS and HOLD until you 1 SET SEE BOTH Blue LEDs come ON RELEASE 2 SEE round Blue LED come ON PROGRAM PRESS and RELEASE 3 SET SEE long Purple LED fl ashing PRESS remote and RELEASE 4 (the button you want to program.) 5 PRESS and RELEASE remote button again SEE both LEDs fl ash Blue and go OFF Note: It is possible to press the remote button too quickly or lightly. If the LED's do not go off, press the remote button several more times to achieve confirmation (the LED's turn off). If the LED's turn red, return to Step 1 and repeat steps 1 through 6. 6 PRESS and RELEASE remote button a third time Programming is complete. This remote button can now be used to operate door opener. Repeat as necessary for other remotes or buttons on the same remote. FCC and IC CERTIFIED This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular situation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try and correct the interference by one or more of the following measures: (a) Re-orient or relocate the receiver antenna, (b) Increase the separation between the opener and receiver, (c) Connect the opener into an outlet on a circuit di erent from that to which the receiver is connected, and (d) Consult your local dealer. Any modi cations or changes to this equipment which are not expressly approved by the manufacturer could void the users authority to operate the equipment. ©2013 GMI Holdings, Inc. DBA The Genie Company 5 SECS SEE long Purple LED come steady ON 2 REMOTE OPERATION• Point Remote at the garage door and press the button. Door will move. • Press the Remote Button again and the door will stop. • Press the Remote Button again and the door will move the opposite way. The door automatically stops at the end of the open or close cycle. 3 LOST OR STOLEN REMOTE ALL Remote Codes will be erased from Opener These instru keypad shown below. 1. Press both lights come ON blue. Release button. 2. Lights go out and Round BLUE light comes ON. 4. Press both simultaneously on the powerhead and hold for 5 seconds. 5. Reprogram the Opener with the remaining Remote(s) (Repeat Section 2 for each remote). Follow these instructions to erase remote codes for ALL other Genie® openers. 1. Press and HOLD the Learn Code button on the powerhead for 10 seconds or until Radio Signal LED indicator goes out. 2. Reprogram the Opener with the remaining Remotes following the programming instructions for that powerhead. 3. Reprogram the Opener with a remote or any other access device using the instructions accompanying those devices. 4 BATTERY REPLACEMENTReplace remote battery with a CR 2032 coin cell battery. 1. Open the remote case using a washer or coin that fi ts into the slot at the top of the remote. 2. Replace battery. Match battery polarity with symbols inside battery housing. 3. Align components and snap case closed. Part Number 38381502287 (powerhead) memory. ctions are for openers with the type PROGRAM and hold until SET PROGRAM 3. Press again and see long SET purple LED fl ashing. and Test remote operation. Remote should not activate door opener. 5 SECS NOTE: For openers manufactured between 1995-1997, use the two upper buttons on the remote For additional information or help contact Customer Service: Call 1-800-35-GENIE or write: GMI Holdings Inc. d/b/a The Genie Company 1 Door Drive Mt. Hope, Ohio 44660 5 SECS 09/2013 |