While Maytag stackable washer and dryer sets are known for their matching designs, easier maintenance, and similar warranties, the failure of the washer is often accompanied by the failure of the dryer and vice versa. For that reason, having a Maytag Stackable Washer and Dryer Troubleshooting guide is paramount. You should know how to fix some issues
which may affect either the washer or dryer or both, and I’m going to help you. Most of these problems are DIY fixable, from a washer dryer that won’t start or spin to another that is not quiet or stops mid-cycle. Our emphasis will not just be on the problems and their probable causes but also on their DIY solutions. And as you’ll notice, the washer and dryer sometimes share the same problem. So, you may fix the other by fixing one, which is a significant advantage. Let’s get
started! In a rush? Check out a summary of the commonest Maytag stackable washer and dryer problems and their causes below: Common Maytag Stackable Washer and Dryer Problems and Their Causes
Below is a guide to use to troubleshoot various Maytag stackable washer and dryer problems: 1. Washer and Dryer Won’t StartMaytag Stackable Washer Will Not StartIf your Maytag stackable washer won’t start, it’s because of a fault touching any of these parts:
Maytag Stackable Dryer Won’t StartYour Maytag dryer will also not start because of a fault involving one of the components below:
2. Washer and Dryer Won’t SpinMaytag Stackable Washer Won’t SpinIf your Maytag stackable washer won’t spin, it’s typically indicative of a fault involving any of the following:
Maytag Stackable Dryer Won’t SpinIf it’s your dryer that won’t spin, it could be because of any of the components below which is faulty:
3. Maytag Stackable Washer Dryer Stops Mid CycleMaytag Washer Stops Mid CycleYour Maytag washer will stop mid-cycle if any of these parts is faulty:
Maytag Dryer Won’t Complete a CycleIf your Maytag dryer doesn’t complete a spin cycle, any of the parts below could be defective:
4. Maytag Stackable Washer Dryer Making NoiseNoisy Maytag WasherYour Maytag washer is making noise because of any of these reasons:
Noisy Maytag DryerLastly, if it’s your dryer that is making noise, the reason is a faulty component, which could be any of the following:
Fix Use the tips shared earlier to inspect each component. If any is defective, replace it. Other Maytag Washer and Dryer ProblemsCheck out the troubleshooting guides below to discover more fixable problems on a Maytag stackable washer or dryer.
How to Reset Maytag Stackable Washer?So, have you just replaced a faulty component? Or perhaps you want to clear an error code. If so, consider resetting your Maytag washer using these steps:
Closing RemarksAbove is a Maytag stackable washer and dryer troubleshooting guide covering four common problems affecting the washer and dryer. Therefore, refer to it the next time your dryer or washer won’t start, spin, complete a cycle or keep the noise down. Also Read:
How do I reset my Maytag stackable washer?Lights Blinking on your Maytag Stacked Laundry Center
To correct this situation, press and hold the Washer Start button for at least 10 seconds until all the display lights turn off. This resets the control, and the washer should operate normally.
Why is my Maytag washer not washing?One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.
How do you reset a stackable washing machine?Motor Reset Procedure:. Unplug the washer for 1 minute from the electrical outlet.. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... . The motor has now been reset and is ready for you to start a cycle.. Why won't my Maytag washer start a cycle?If your Maytag washing machine won't start but has power, check the control panel to make sure the right functions are selected. If the Control Lock feature is selected, all control panel functions will be locked, preventing an accidental start.
|